HeatnBond Lite Iron-On Adhesive Tape, 7/8 in x 10yds

(385)

Write Review

$ 1.50

Add to Cart

Qty

In stock

Description

sku : 3348

HeatnBond Lite is a roll of iron-on, sewable, double-sided adhesive for bonding fabric without extra weight or stiffness. Use it in place of pinning or basting. Just stitch right thru the adhered layers of fabric.

Product Details

7/8 in x 10 yards (22.2 mm x 9.1 m)
Heat activated
Permanent
Double-sided adhesive
For use on fabric
Doesn’t gum up needles
Proudly made in the USA

General Directions

Pre-wash all materials without fabric softeners. Pretest adhesive on materials before starting project.

Preheat iron to medium heat, No steam. Place adhesive on back of material to be bonded (paper liner should face up).

Place and hold iron on the paper liner for 2 seconds. Repeat until entire surface is bonded. Allow to cool.

Cut to size or shape needed. Peel off paper liner.

Place material, adhesive side down, on top of project. Press and hold iron for
6 seconds on each section until entire piece is bonded.

Times listed above are for cotton. Iron thick fabrics an additional 2 seconds from the back of the project.

Hand or Machine sew along edges.

Tips

If stitching is NOT desired, use HeatnBond Ultrahold in the red package.
Do not touch iron directly to the adhesive sheet. Do not iron directly to your ironing board
HeatnBond LITE sheets can be run thru an INKJET printer (NOT a laser jet or copy machine). Cut to printer size, feed into printer to print on the paper side, set printer to Draft or Transparency setting, allow to dry before touching. Run any lettering in mirror setting so they are the correct orientation when cut from the fabric..
Must be sewn or otherwise attached before washing. Machine wash cold and dry on low heat or no heat (and in accordance to garment / fabric washing directions). Avoid repeated or excessive ironing to the area after fusing.

sku : 3348 HeatnBond Lite is a roll of iron-on, sewable, double-sided adhesive for bonding fabric without extra weight or stiffness. Use it in place of pinning or basting. Just stitch right thru the adhered layers of fabric. Product Details 7/8 in x 10 yards (22.2 mm x 9.1 m) Heat activated Permanent Double-sided adhesive For use on fabric Doesn’t gum up needles Proudly made in the USA General Directions Pre-wash all materials without fabric softeners. Pretest adhesive on materials before starting project. Preheat iron to medium heat, No steam. Place adhesive on back of material to be bonded (paper liner should face up). Place and hold iron on the paper liner for 2 seconds. Repeat until entire surface is bonded. Allow to cool. Cut to size or shape needed. Peel off paper liner. Place material, adhesive side down, on top of project. Press and hold iron for6 seconds on each section until entire piece is bonded. Times listed above are for cotton. Iron thick fabrics an additional 2 seconds from the back of the project. Hand or Machine sew along edges. Tips If stitching is NOT desired, use HeatnBond Ultrahold in the red package. Do not touch iron directly to the adhesive sheet. Do not iron directly to your ironing board HeatnBond LITE sheets can be run thru an INKJET printer (NOT a laser jet or copy machine). Cut to printer size, feed into printer to print on the paper side, set printer to Draft or Transparency setting, allow to dry before touching. Run any lettering in mirror setting so they are the correct orientation when cut from the fabric.. Must be sewn or otherwise attached before washing. Machine wash cold and dry on low heat or no heat (and in accordance to garment / fabric washing directions). Avoid repeated or excessive ironing to the area after fusing.

HeatnBond Lite is a roll of iron-on, sewable, double-sided adhesive for bonding fabric without extra weight or stiffness. Use it in place of pinning