A high build acrylic primer surfacer that easily fills grind marks, sand scratches and other minor surface imperfections. Sands easily to an ultra-fine finish with minimal shrinkage. Can be applied to properly prepared metal, body filler, polyester glazing putty, wood, fiberglass and aged sanded OEM topcoats.
SUBSTRATES
- Properly Prepared Steel, Galvanized and Aluminum
- Fiberglass
- SMC
- Rigid Plastics
- Body Filler or Putty
- Epoxy Primer
- Self-Etch Primer
NOTE: For best adhesion and corrosion resistance, treat all bare metal areas larger than a quarter in diameter with a self-etch primer prior to application.
CLEANING
- Surface must be clean and free of dirt, oil, grease and wax
- Solvent clean all areas to be coated with a quality wax and grease remover and wipe dry with a clean, dry cloth
- To solvent clean raw, exposed fiberglass, it is recommended to clean exposed area with acetone.
PREPARATION
Untreated Steel, Galvanized Steel and Bare Aluminum
- Sand surface with 180 - 220 grit sandpaper. Blow off the surface with an air blow gun and solvent clean all areas to be coated with a quality wax and grease remover and wipe dry with a clean, dry cloth.
- Follow paint company’s recommendations for surface prep and recoat of self-etch primer
Pre-Painted Surfaces
- Sand repair area and featheredge using 80, 180, 220 and finish with 320 grit sandpaper on a random orbital sander.
- Final clean with a quality wax and grease remover to remove sanding residue before priming.Sand repair area and featheredge using 180 grit, 220 grit and finish with 320 grit sandpaper on a random orbital sander
- Final clean with a quality wax and grease remover to remove sanding residue prior to application
Body Filler or Putty
- Finish sanding body filler or putty with 180-220 grit sandpaper
- Featheredge with 320 grit sandpaper
- Blow off the surface with an air blow gun
MIXING
- Shake and stir thoroughly before mixing
- Reduce 125% with #2296 Universal Zero VOC Reducer
- Mix thoroughly before pouring primer into the gun cup
APPLICATION
- Use a primer gun with a 1.4 to 1.8 fluid nozzle/air cap (Spray at paint gun manufacturer’s recommended air pressure)
- Apply 2-3 medium wet coats allowing 5-10 minutes flash time between coats
- FINISH
- Ready to sand in about 60 minutes depending on film build
- Once dry, sand with 400-600 grit sandpaper prior to next step
FINISH
- Ready to sand in about 60 minutes depending on film build
- Once dry, sand with 400-600 grit sandpaper prior to next step
Product# 2274 102274
Featured
Evercoat Dura-Build Acrylic Primer Surfacer - Gray, 2274 , 1 Gallon
Primers / Clears Archives - ITW Evercoat
Paint - Primer Surfacers - Lacquer Based
Convenient Primer: Easily fills grind marks, sand scratches, and other minor surface imperfections Easily Applicable Primer: Use a primer gun with a
Evercoat Dura Build Acrylic Primer Surfacer for Body Filler, Putty, Fiberglass and More - 128 Fl Oz
Evercoat Primers
EverCoat 60478ZP Dura Build Acrylic Primer Gray Gallon 102
Auto Paint & Primer for Body Repair Shops
Evercoat Bumper To Bumper
Optex Super Build 4:1 Primer highlights dents low spots scratches and other surface imperfections while at the same time eliminating the need for messy carbon black powdered guide coats. This 4:1 primer sprays on pink and turns gray as it is sanded revealing high spots while low spots and scratches remain pink.
Fibreglass Evercoat Optex Super Build 4:1 Primer, Gallon
Evercoat Dura Build Acrylic Primer Red Oxide Quart 2283 for sale online
517neBEbgqL._SL1000.jpg?v=1479172776
Polyester Primer
Auto Body Tools & Body Shop Supplies
102261 - Dura Build 2.1 Gray Quart - ITW Evercoat