Wood Glue Applicator Glue Syringe 20 mL Syringe Glue Applicator

If you need a little glue in just the right place or even need a lot of glue in a hidden joint on your project, use the DCT Syringe Applicator. It allows you to apply glue under pressure (up to 550 PSI) in areas such as small openings of dovetail sockets. The glue chamber is approximately 3 inches (7.6cm) in length and
If you need a little glue in just the right place or even need a lot of glue in a hidden joint on your project, use the DCT Syringe Applicator. It allows you to apply glue under pressure (up to 550 PSI) in areas such as small openings of dovetail sockets. The glue chamber is approximately 3 inches (7.6cm) in length and includes 5 mL, 10 mL, 15 mL, 20 mL markings with single ticks in increments of 1 mL (CCs). It holds 20 mL (0.7 fl oz). Use with water-based (water-soluble) wood glues and silicones for maximum syringe longevity and easy cleaning. Simply fill the glue chamber and push down on the plunger to apply glue to your application. This package includes a syringe with a 1/16-inch tip and 1/32-inch tip for your convenience. Glue not included.

REPAIR DELICATE ASSEMBLIES: The DCT Glue Applicator Syringe provides up to 550 PSI of pressurized power to apply glue in small places; Injector syringe holds 20 mL (0.7 fl oz) of water-based wood glues; For veneering, lutherie, craft and hobby gluing, furniture joints, wicker chairs, wooden screen doors, laminates, cabinetry, stair rails and banisters, floor squeaks, or even jewelry making and cake decorating; Additionally use for mechanical work to place fine beads of silicone gasket material

EASY TO LOAD: Includes an easy fill-port design that allows you to load glue into the chamber two different ways; Method 1 – Unscrew top where handle is, pull out plunger, pour in glue, screw top back on, flip syringe with tip upwards, remove air, screw on your desired tip, and apply; Method 2 – Remove brass tip, submerge this end in a glue container, pull plunger back until full, reinstall brass tip, and apply

EASY TO DISPENSE: Dispensing syringe allows you to apply glue under pressure; If you do not enough space to get glue into a joint on your project, instead of disassembly your project, you can drill a small hole and inject glue through the hole into the joint using this wood glue injector

MAINTENANCE: Moisten O-ring before inserting plunger and screwing brass tip into barrel; Do not allow glue to dry in the injector (injector may be immersed in water to prevent glue from hardening); Clean well after use; Removable plunger and brass nozzle allow you to clean thoroughly with warm water and brush (not included) (do not use solvent); Regularly lubricate and use cooking oil on O-ring for a smooth, airtight seal

PACKAGE CONTENTS: Package includes (1) adhesive syringe and (2) brass tips with O-rings (1/16-inch and 1/32-inch nozzles); Wood glue not included

California Residents Prop 65 warning: Products may contain a chemical known to the State of California to cause cancer, birth defects or other reproductive harm.

This product has a manufacturer warranty against defects in materials and workmanship for a period of ONE (1) YEAR from the date of original retail purchase. See our Seller Return Policy for more details.

If you need a little glue in just the right place or even need a lot of glue in a hidden joint on your project, use the DCT Syringe Applicator. It allows you to apply glue under pressure (up to 550 PSI) in areas such as small openings of dovetail sockets. The glue chamber is approximately 3 inches (7.6cm) in length and includes 5 mL, 10 mL, 15 mL, 20 mL markings with single ticks in increments of 1 mL (CCs). It holds 20 mL (0.7 fl oz). Use with water-based (water-soluble) wood glues and silicones for maximum syringe longevity and easy cleaning. Simply fill the glue chamber and push down on the plunger to apply glue to your application. This package includes a syringe with a 1/16-inch tip and 1/32-inch tip for your convenience. Glue not included.REPAIR DELICATE ASSEMBLIES: The DCT Glue Applicator Syringe provides up to 550 PSI of pressurized power to apply glue in small places; Injector syringe holds 20 mL (0.7 fl oz) of water-based wood glues; For veneering, lutherie, craft and hobby gluing, furniture joints, wicker chairs, wooden screen doors, laminates, cabinetry, stair rails and banisters, floor squeaks, or even jewelry making and cake decorating; Additionally use for mechanical work to place fine beads of silicone gasket materialEASY TO LOAD: Includes an easy fill-port design that allows you to load glue into the chamber two different ways; Method 1 – Unscrew top where handle is, pull out plunger, pour in glue, screw top back on, flip syringe with tip upwards, remove air, screw on your desired tip, and apply; Method 2 – Remove brass tip, submerge this end in a glue container, pull plunger back until full, reinstall brass tip, and applyEASY TO DISPENSE: Dispensing syringe allows you to apply glue under pressure; If you do not enough space to get glue into a joint on your project, instead of disassembly your project, you can drill a small hole and inject glue through the hole into the joint using this wood glue injectorMAINTENANCE: Moisten O-ring before inserting plunger and screwing brass tip into barrel; Do not allow glue to dry in the injector (injector may be immersed in water to prevent glue from hardening); Clean well after use; Removable plunger and brass nozzle allow you to clean thoroughly with warm water and brush (not included) (do not use solvent); Regularly lubricate and use cooking oil on O-ring for a smooth, airtight sealPACKAGE CONTENTS: Package includes (1) adhesive syringe and (2) brass tips with O-rings (1/16-inch and 1/32-inch nozzles); Wood glue not includedCalifornia Residents Prop 65 warning: Products may contain a chemical known to the State of California to cause cancer, birth defects or other reproductive harm.This product has a manufacturer warranty against defects in materials and workmanship for a period of ONE (1) YEAR from the date of original retail purchase. See our Seller Return Policy for more details.

15 Pack Blunt Tip Syringe Glue Syring 20ml 10ml 5ml 3ml 1ml Glue Syringe Syringes For Oil Glue Applicator Science Lab - AliExpress

20ml Plastic Syringe with 10Ga Blunt Tip Needle 4 and Storage Caps - Great for Refilling Vegetable Glycerin - Glue Applicator - Oil Dispensing : Industrial & Scientific

Luer Lock Syringe - Polypropylene material, good air tightness, measurements are easy to read. 4 Inch Blunt Tip Needles - extra long blunt dispensing

20 ml Syringe with Luer Lock Needles 4 and Storage Cap | Oil Injector | Glue Dispensing Applicator

Wood Glue Applicator Glue Syringe 20 mL Syringe Glue Applicator & Tips – DeadwoodCraftedTools

Wood Glue Applicator Glue Syringe 20 mL Syringe Glue Applicator & Tips – DeadwoodCraftedTools

20Pcs 10 Ml/20 Ml Luer Lock Syringe Plastic Syringes For Scientific Labs, Feeding Pets Animals, Oil Or Glue Applicator - AliExpress

30Pack 20ml Plastic Syringe Sterile Individual Wrap with Tip Cap&Soft Tube, Measurement and Dispensing Syringe Tools for Science Labs,Liquid Measuring,Feeding Pets,Oil or Glue Applicator (20ml, 30) - Yahoo Shopping

If you need a little glue in just the right place or even need a lot of glue in a hidden joint on your project, use the DCT Syringe Applicator. It

DCT | Wood Glue Applicator Glue Syringe and Tips – 20 mL Syringe Glue Applicator

DCT Wood Glue Applicator Glue Syringe and Tips – 20 mL Syringe Glue Applicator

Wood Glue Applicator Glue Syringe 20 mL Syringe Glue Applicator

System Three 60cc Epoxy Syringes are for larger cracks and bigger void filling jobs. The main difference in these syringes is the opening (needle) through which the glue is pushed. It’s large enough to easily handle the thickening epoxy so you can fill cracks and voids with ease without wearing out your hand.

System Three Syringes, 60cc, 2-Pack